[. . . ] CONTENTS
1
Before use
OWNER'S MANUAL
3LCD DATA PROJECTOR
TLP-B2U
SAFETY PRECAUTIONS
WARNING:
CONTENTS
2
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Before use
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] 29 " " is displayed on the screen if the projector does not receive any signal from the connected equipment. Due to the lamp characteristic, flickers may occasionally occur in a picture. While operating the projector, " " may be displayed on the screen. " " is displayed on the screen if: - The projector is too hot. Turn the projector off, and leave it for a while, and then turn it on again. - The ambient temperature is too high, use the projector under moderately cold temperature. " " is displayed on the screen if the air filter is dusty, the ventilation is impaired. 55
Turning the power off
CONTENTS
28
1 2
Press ON/STANDBY after using the projector.
An instruction message appears.
Press ON/STANDBY again.
The LAMP indicator turns off, and the projector turns to standby mode. (The ON indicator lights in orange. )
Operations
ON
LAMP
ON
LAMP
ON
(Orange)
LAMP
(Off)
(Orange) Flashing (Green)
(Orange) Flashing (Orange)
3
Notes
After confirming the LAMP indicator turns off, unplug the power cord.
The ON indicator turns off.
Indicators
Immediately after the power off, the projector may not be turned on while the LAMP indicator is flashing in green. Even after turning the power off, the intake and exhaust fans continue to work for a while to cool the inside of the projector. (When the lamp indicator is flashing in orange. ) Before unplugging the power cord, make sure that the LAMP indicator is turned off.
Correcting the keystone distortion
CONTENTS
29
A picture may be expanded on the upper side if projected upward from the projector lifted up by the foot adjuster. The projector can correct this keystone distortion automatically.
Operations
KEY STONE
Press KEYSTONE.
The keystone distortion on the picture projected is automatically corrected and the fine adjustment screen of the keystone distortion correction appears. /
To correct further, make the "Keystone" adjustment on the menu. 38
Cutting off the picture and sound temporarily
MUTE
CONTENTS
30
Press MUTE.
The sound and picture are cut off temporarily. To restore, press MUTE again.
Operations
Freezing the picture
FREEZE
CONTENTS
31
Press FREEZE.
The picture freezes. To release the picture, press FREEZE again.
Note
If you perform other operation while freezing the picture, the picture freezing operation is released.
Operations
Enlarging the picture size
You can enlarge the picture size projected.
ZOOM
CONTENTS
32
Press ZOOM (+).
+ Each time the ZOOM (+) button is pressed, the enlargement ratio increases. / / / buttons shifts the picture part
ZOOM
+
Operations
ENTER
RESET
Press the RESET button to cancel the zoom operation.
Notes
Picture enlargement display will return to the normal size after the power turns off and on again. The picture may not be projected properly while shifting the picture. Since the electrical digital zoom system is employed, the picture quality may be degraded in accordance with the enlargement ratio. If you perform other operation, the zoom operation is cancelled.
Menu screen structure
Most of adjustments and settings are made on the menu screen. Quick menu and full menu are provided in the menu screen.
CONTENTS
33
Quick menu
QUICK MENU Contrast Brightness Phase Auto keystone FULL MENU
Full menu You can set the Basic setting used frequently. 34
Picture adjustment Contrast Brightness Color Tint Sharpness
You can set all kinds of setting.
Contrast Brightness Phase Auto keystone FULL MENU
To adjust the contrast. [. . . ] 1 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 (3m) Control cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Soft case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CONTENTS
65
The design and specifications are subject to change without notice.
Trademarks NEC, PC-98 series are trademarks of NEC Corporation. [. . . ]